SARPOL RP08

Anti-wear and shock-resistant paste resin

SARPOL RP08 is a two-component epoxy paste, rubber-modified and ceramic-filled, combining abrasion resistance and impact resistance. It is designed to protect, rebuild, and repair high-wear areas of equipment and machinery. The product guarantees:

Impact resistance and protection of metal surfaces from abrasive agents
Refurbishment and repair of worn metal parts
Excellent abrasion resistance thanks to the ceramic filler
for use on vertical and ceiling surfaces without dripping

The product typically operates in a temperature range of -30 °C to +120 °C. Typical applications include:

Flow deflectors
truckloads
Curves and slides
tramogge
Plant and machinery exposed to abrasion and impact

SARPOL RP08 provides the following product features:

MSDS A

MSDS B

STANDARD PRODUCT DIMENSIONS

Technology	Epoxy
Chemistry Type	Epoxy
Waiting (Resin)	Pasta Grigio
Brake pads (hardener)	Black pasta
Appearance – Mixture	Dark Grey Paste
Components	2 parts – Resin & Hardener
Mixing Ratio (Weight – Volume) Resin: Hardener	2 : 1
Polymerization	At ambient temperature after mixing
Application	Wear-Resistant Coating – Impact Resistant
Application Temperature	59 – 86°F
Operating Temperature	120°C max
Advantages	Impact Resistant Refurbishment and repair of worn metal parts Protecting metal surfaces from abrasive agents Ceramic fill – for excellent abrasion resistance Thixotropic – provides abrasion resistance on vertical and overhead surfaces

TYPICAL CHARACTERISTICS OF MATERIALS

Properties of Part A
Density @ 25 °C, ISO 1675, g/cm³	1,7
Viscosity	Paste
Part B Properties
Density @ 25 °C, ISO 1675, g/cm³	1,6
Viscosity	Paste
Properties of A + B Mixture
Density @ 25 °C, ISO 1675, g/cm³	1,67
Viscosity	Paste
Hardening Properties
Open Time, ASTM D2471 minutes	30
Curing Time @ 25 °C, hours	6
Coverage
To achieve a thickness of 6 mm	res 0.1 m² / kg

GENERAL INFORMATION

This product is not recommended for use in oxygen-rich and/or pure oxygen systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.

For information on the safe handling of this product, please refer to the Safety Data Sheet (SDS).

INSTRUCTIONS FOR USE

Surface Preparation

Proper surface preparation is critical for the long-term performance of this product. Exact requirements vary based on the severity of the application, anticipated service life, and the initial conditions of the substrate.

All welds and weld spatter must be ground flush. Blast all surfaces to be coated with angular grit to a profile of 50-70 microns and a near-white metal cleaning degree (SIS SA 2½ /SSPC-SP 10).
After sandblasting, metal surfaces must be cleaned and coated before any oxidation.
For vertical or ceiling applications, the application of expanded metal mesh is recommended.

Method of Application

Film thickness per layer: minimum 6 mm.
Apply the material to the prepared surface by first forcing a thin layer deep into the consistency of the substrate.
Immediately thereafter, build up to the required finished thickness.
At 25°C, the working time is 30 minutes. Functional hardening (handling) in 6 hours.

Check:

Visually inspect for holes and voids immediately after application.

Once the coating has cured, repeat the visual inspection to confirm the absence of holes, voids, or damaged areas.

Coating thickness control, especially in critical areas.

Caution: Use an approved positive pressure air respirator when welding or cutting near the cured compound. Do not use open flames on the compound.

Repairs

Any voids, holes, or thin areas found in the coating can be repaired by lightly abrading, cleaning the area, and applying additional product.

Cleaning

Immediately after use, tools must be cleaned with a suitable detergent, e.g., a solvent such as acetone or isopropyl alcohol. Once hardened, the material can only be removed mechanically.

Not for the product specifications

The technical data contained herein is for reference purposes only. Please contact the technical department for assistance and recommendations regarding specifications for this product.

Storage

Store the product in the closed container in a dry place. Storage information may be indicated on the product container's label.

Optimal storage: 8 to 21 °C. Storage below 8 °C or above 28 °C may negatively affect the product's properties. Material removed from containers may become contaminated during use. Do not return product to the original container. SARO Srl cannot assume responsibility for product that has been contaminated or stored under conditions other than those indicated above. If further information is required, please contact technical support or your local representative/vendor.

Warnings

The information provided in this technical data sheet (TDS), including recommendations for the use and application of the product, is based on the manufacturer's knowledge and experience as of the date of this TDS. The product may have a variety of different applications, as well as different application and working conditions in the environment of use beyond the manufacturer's control. SARO Srl, therefore, is not responsible for the suitability of the product for the production processes and conditions for which it is used, nor for the intended applications and results. It is strongly recommended to conduct your own tests to confirm its suitability. Any liability relating to the information contained in the technical data sheet or any other written or oral recommendation regarding the product is excluded.

SARO Srl expressly disclaims all express or implied warranties, including warranties of merchantability or fitness for a particular purpose, arising from the sale or use of SARO Srl products. SARO Srl expressly disclaims any liability for consequential or incidental damages of any kind, including lost profits.